| ES891.2 | ES892.2 | |
Size and weight |
||
| Dimensions (HxWxD) | 63 mm x 215 mm x 230 mm (2.47 in x 8.46 in x 9.05 in) | |
| Weight | 2.9 kg / 6.4 lbs | |
Environment |
||
| Temperature range | -40 °C to +70 °C / -40 °F to +158 °F (operation) | |
| -40 °C to +85 °C / -40 °F to +185 °F (storage) | ||
| Relative humidity | 85 % (Operation) 95 % (Storage), non-condensing | |
| Tested for | Mechanical shock, vibration, fall, temperature alteration, according to EN 60068 and ISO 16750 | |
| Protection class | IP44 | |
| Altitude | Maximum 5000 m / 16.400 ft height above sea level | |
| Standby current Range | 17 mA (typ.) at 12 V DC | |
| 25 mA (max.) | ||
| Operating Current Range | 5 A (Max) in operation (12 V DC) | |
Power supply |
||
| Operating voltage | 7 V – 29 V DC | |
| Power consumption at 12 V DC | Typically 2.2 A in operation and 12 mA in standby | |
| Energy management (wake-up / standby) | Power-on/off when Ethernet traffic starts/stops (PC or upstream module on/off). | |
| Configurable: Power-on when CAN/ CAN FD/ FlexRay traffic starts | ||
| Protection | Reverse voltage protection up to 32 V, load dump protection | |
Host interface |
||
| Gigabit Ethernet | 1x 100/1000Base-T | |
| Fast Ethernet | 1x XETK ECU interface. Alternatively: 1x 10/100Base-T for the connection of measurement and interface modules | |
| Gigabit Ethernet | 2x FETK ECU interfaces with host-side XCP-on-Ethernet support. | |
| With the help of an adapter cable, ETKs of type ETK-S20.1 and ETK-S21.1 can be connected. | ||
| Alternatively: 2x 10/100/1000Base-T for the connection of measurement and interface modules | ||
Device interfaces |
||
| Power supply | Of connected ES4xx / ES6xx measurement modules and XETKs | |
| Synchronization | Resolution: 1 µs | |
Bus interfaces |
||
| 5 x CAN/CAN FD/ CAN XL or 3 x CAN/CAN FD/ CAN XL and 1 x Flex Ray , 1 X LIN | 5 x CAN/CAN FD/ CAN XL or 3 x CAN/CAN FD/ CAN XL and 1 X LIN | |
| CAN/CAN FD/ CAN XL [1] | 5 channels high-speed CAN (2.0 A and 2.0B). | |
| Transfer of CAN FD data frames up to 64 Byte and rates up to 5 Mbit/s | ||
| CAN Transceiver: NXP TJA1462 ( signal improvement capability using SIC) | ||
| CAN: 1Mbit/ sec (Max Speed) 8 Bytes (Payload), CAN FD SIC: 5Mbit/ sec (higher number of nodes and sub-topology), 8Mbit/ sec (point to point connection) 64 Bytes (Payload), CAN XL: 8 Mbit/ sec 2048 Bytes (Payload) | ||
| FlexRay[1] | 1 FlexRay V2.1 interface with 2 channels A and B or one additional internal node for synchronizing the FlexRay bus | |
| Flex Ray Transceiver: NXP TJA1082, 254 Bytes ( Max. Payload), 10 Mbit/ sec (Max Speed) | ||
| LIN | 1 channel LIN V2.2A | |
| LIN Transceiver: MCZ33661EF | ||
Status display |
||
| LEDs | Status of operation, interfaces and synchronization | |
Compatible hardware |
||
| PC/ ETAS upstream modules | PC with Ethernet port, ES820 Drive Recorder | |
| ETAS downstream modules | ES523, ES592, ES593-D, ES595, ES600.2, and ES88x Network and Interface Modules, ES4xx and ES6xx Measurement Modules, ES910.3 Prototyping and Interface Module, ES930 Multi-I/O Module as well as the XETK- and BR-XETK (with CBEB105 BroadR-Reach Media Converter) | |
Support by software |
||
| ETAS INCA | Supports onward INCA V7.4.3 | |
| Firmware Update | Supported onward HSP V13.7.0 | |
| 3rd party SW support | Enables 3rd party usage (BOA, XCP) https://www.etas.services/en/downloadcenter/18102.php | |
Wakeup Management |
||
| Standby mode : System automatically switches to standby mode when none of the host ethernet or AE nodes, CAN-FD, CAN, CAN XL FlexRay and LIN nodes detects any data traffic signal | Standby mode : System automatically switches to standby mode when none of the host ethernet or AE nodes, CAN-FD, CAN and LIN nodes detects any data traffic signal | |
| Wakeup mode : System automatically switches to On mode when either host ethernet or Data traffic or at least one of the AE nodes, CAN-FD, CAN, CAN XL FlexRay and LIN node detects any data traffic | Wakeup mode : System automatically switches to On mode when either host ethernet or Data traffic or at least one of the AE nodes, CAN-FD, CAN and LIN node detects any data traffic | |
Note |
||
| [1] | When the FlexRay interface of the ES891 module is not used, the ES891 module provides five CAN / CAN FD channels also. | |
This product has been developed and released for use in automotive applications. For usage in other domains please contact your ETAS representative.