CPU interface |
|
| Bus interface | 2.5 V bus interface (3.3 V tolerant) for non-multiplexed bus |
| 32 bit | |
| Supported processors | For Infineon TC1792, TC1793, TC1793ED, TC1796, TC1796ED, TC1797, TC1797ED processors |
| For a complete list of supported microprocessors, please refer to the product's User's Guide. | |
| Configuration | Project-specific configuration for memory configurations stored in EEPROM |
Board |
|
| Dimensions (HxWxD) | 9.9 x 72 x 52 mm / 0.39 x 2.83 x 2.05 in |
Power supply |
|
| Input voltage | 4.3 V to 18 V |
| Stand-by: min. 4.3 V | |
| Input current at 12 V | approx. 100 mA normal operation |
| approx. 20 mA stand-by | |
Memory emulation |
|
| Emulation memory | Two memory pages with 1024 KB data memory each, minimum access time 18 nsec |
| Measured data memory | Within the emulation memory, freely configurable |
| Flash memory | 1024 KB flash (data) |
Host interface |
|
| Serial interface | 100 Mbit/s |
| Double-shielded line, max. 30 m/100 ft | |
| Electrically isolated | |
| Debug interface | JTAG debugging interface connector |
Operation temperature |
|
| Temperature range | -40 °C to +110 °C /-40 °F to +230 °F |
This product has been developed and released for use in automotive applications. For usage in other domains please contact your ETAS representative.
Ordering Information
1 – Interface Connection
2 – ETK Connection (for all 100 Mbit ETKs)
3 – Power Supply Connection
4 – ECU Connection
5 – Ethernet PC Connection
| Order Name | Short Name | Order Number |
|---|---|---|
| ETK-T2.2 | ||
| ETKT-2.2A emulator probe with 441 pin adapter for a TC1792, TC1793, TC1796 or TC1797 ECU, with 1MB memory per page | ETK‑T2.2A | F‑00K‑107‑061 |
 |
||
| Optional Accessories for ETK-T2.2 | ||
| 1 – Interface Connection (all 100 Mbit ETKs to ES59x, ES690, ES910) | ||
| ETK Interface Cable 100 Mbit/s, Lemo 1B FFG - Lemo 1B FFG (4mc-4mc), 3 m | CBM150‑3 | F‑00K‑102‑556 |
 |
||
| ETK Interface Cable 100 Mbit/s, Lemo 1B FFG - Lemo 1B FFG (4mc-4mc), 5 m | CBM150‑5 | F‑00K‑102‑557 |
|
||
| ETK Interface Cable 100 Mbit/s, Lemo 1B FFG - Lemo 1B FFG (4mc-4mc), 10 m | CBM150‑10 | F‑00K‑102‑553 |
|
||
| 2 – ETK Connection (for all 100 Mbit ETKs) | ||
| ETK ECU Adapter Cable, Shield on ECU-Housing, Lemo 1B PHG - JST PHR (4fc-5fc), 0m6 | KA54 | F‑00K‑001‑302 |
 |
||
| ETK ECU Adapter Cable, Lemo 1B PHG - JST PHR (4fc-5fc), 0m6 | KA55 | F‑00K‑001‑303 |
 |
||
| ETK ECU Adapter Cable, Shield on ECU-Housing, Lemo 1B HMG - JST PHG (4fc-5fc), 0m085 | CBAM200.2‑0m085 | F‑00K‑104‑312 |
 |
||
| ETK ECU Adapter Cable, Shield on ECU-housing, Lemo 1B HMG - JST PHG (4fc-5fc), 0m130 | CBAM200‑0m130 | F‑00K‑104‑852 |
|
||
| ETK ECU Adapter Cable, pre-assembled into PG9 screwing, shield on ECU- Housing, Lemo 1B PHG - JST PHR (4fc-5fc), 0m50 | CBAM261‑0m5 | F‑00K‑107‑754 |
 |
||
| 2&3 – Combined ETK ECU Adapter and Power Supply Cable (all 100 Mbit ETKs) | ||
| ETK ECU Adapter and Power Supply Cable, Lemo 1B PHG - JST PHR (4fc-5fc) / Lemo 0B PHG - open wires (2fc-2c), 0m6 | CBAM210‑0m6 | F‑00K‑104‑873 |
 |
||
| ETK ECU Adapter and Power Supply Cable, Shield on ECU-Housing, Lemo 1B PHG - JST PHR (4fc-5fc) / Lemo 0B PHG - open wires (2fc-2c), 0m60 | CBAM220‑0m6 | F‑00K‑105‑075 |
 |
||
| ETK ECU Adapter and Power Supply Cable, pre-assembled into PG9 screwing, shield on ECU-Housing, Lemo 1B PHG - JST PHR (4fc-5fc) / Lemo 0B PHG - JST PAP (2fc-2fc), 0m50 | CBAM260‑0m5 | F‑00K‑107‑753 |
 |
||
| 3 – Power Supply Connection | ||
| ETK Power Supply Cable with Filter Coil, JST PHR - open wires (2fc-2c), 0m19 | ETV2 | F‑00K‑000‑593 |
 |
||
| ETK Power Supply Cable for External Supply, with Filter Coil, Lemo 0B EGG - open wire (2fc-1c), 0m2 | KA50 | F‑00K‑000‑940 |
 |
||
| External Power Supply Cable for ETKs, Lemo 0B - FGG open wires (2fc-1c), 2 m | K70.1 | F‑00K‑109‑270 |
 |
||
| ETK power supply for 6-36V DC input | ETP1 | F‑00K‑000‑624 |
| ETK power supply for 4,3-36V DC input, with galvanic isolation | ETP2 | F‑00K‑104‑010 |
| Debugger Connection | ||
| Debug Adapter from Infineon OCDS1-Plug to ETK | ETAF5.0 | F‑00K‑104‑220 |
| Microcontroller Power Supply for ECU (Microcontroller specific) | ||
| Power supply for ECU with 1,5V microcontroller | ETP4 | F‑00K‑104‑914 |
| Power supply for ECU with 1,3V microcontroller | ETP5 | F‑00K‑106‑798 |
| ECU Connection Protection Cap (for CBAM230, CBAM240) | ||
| Cap to protect open Lemo 1B sockets against dirt, cost effective | CAP_LEMO_1B_LC | F‑00K‑105‑683 |
 |
||
| 4 – ECU Connection The ETK is directly put on the ECU without an additional cable. |
||
5 – Ethernet PC Connection
Further information on the Ethernet PC Connection, can be found in the cable page Ethernet Connection.
Note: This list contains only a selection of available adapters. A comprehensive overview is available in the User Guide of each ETK.